CNC高壓清洗機的類型和壓力大小盡管有所不同，可是它的基本構造、大部構成、作業原理等大致一樣，只不過是用處各有側重罷了。下面小編為大家總結了CNC高壓清洗機使用的八大步。

Although the brand type and pressure size of CNC high-pressure cleaning machine are different, its basic structure, most of its composition, operating principle, etc. are roughly the same, but each has its own emphasis on its use. The following section summarizes the eight steps of using CNC high-pressure cleaning machine.

1：CNC高壓清洗機在開機前應作的預備：主要是要做好相關查看，主要的是潤滑油要在規定的油位，通常應是在觀察窗上下兩刻線之間的方位。查看各個聯系方位是不是嚴密，使構造銜接處在杰出狀況。

1: Preparations for CNC high-pressure washer before starting up: it is mainly to make relevant checks, and the main thing is that the lubricating oil should be at the specified oil level, usually at the position between the upper and lower reticles of the observation window. Check whether the contact directions are tight, so that the structural connection is in an outstanding condition.

2：把高壓泵的進水管接口與進水管相銜接，而且固定好，使它不漏氣不漏水。然后把另一端和自來水水管銜接或刺進供水池供水桶。并查看雜質過濾器是不是無缺。

2: Connect the water inlet pipe interface of the high-pressure pump with the water inlet pipe, and fix it to make it air tight and water tight. Then connect the other end with the tap water pipe or pierce it into the water supply tank for water supply. Check whether the impurity filter is intact.

3：CNC高壓清洗機把高壓泵的出水口與出水高壓膠管相銜接，膠管另一端則與高壓噴槍的槍桿相銜接。

3: The CNC high-pressure washer connects the water outlet of the high-pressure pump with the outlet high-pressure hose, and the other end of the hose is connected with the barrel of the high-pressure spray gun.

4：把CNC高壓清洗機與供電線路相銜接。銜接時要查看電源電壓是不是匹配，要辨明應該用220V的仍是應該用380V的電壓。在準確銜接電源后，就能夠啟動設備的開關了。摳動高壓噴槍的操控組織扳機，等高壓泵內的空氣排完后，高壓水射流就能夠噴出了。

4: Connect the CNC high-pressure washer with the power supply line. During connection, check whether the power supply voltage is matched, and distinguish whether 220V or 380V should be used. After the power supply is correctly connected, the switch of the equipment can be started. Pull the control and organization trigger of the high-pressure spray gun, and after the air in the high-pressure pump is exhausted, the high-pressure water jet can be ejected.

5：易損壞物體外表，假如CNC高壓清洗機太遠，清潔效果會下降。要總結和把握操作的經歷。假如清潔間歇時刻超過十分鐘時，要關掉高壓清潔設備的電源開關，翻開高壓噴槍閥，進行卸壓，這么有利于維護高壓泵的零部件，使之延伸運用壽命。

5: It is easy to damage the appearance of objects. If the CNC high-pressure cleaner is too far away, the cleaning effect will decline. Summarize and grasp the experience of operation. If the cleaning interval exceeds ten minutes, turn off the power switch of the high-pressure cleaning equipment, turn on the high-pressure spray gun valve and relieve the pressure, which is conducive to maintaining the parts of the high-pressure pump and extending its service life.

6：在履行高壓清潔使命時，要用高壓泵的額外壓力作業，一般不要用很高壓力進行清潔，CNC高壓清洗機若非常有必要用很高壓力，也要操控在30分鐘以內，及時康復到額外壓力作業。

6: When performing the high-pressure cleaning mission, the extra pressure operation of the high-pressure pump should be used, and generally do not use very high pressure for cleaning. If it is very necessary to use very high pressure, the CNC high-pressure washer should also be controlled within 30 minutes to recover to the extra pressure operation in time.

7：完結高壓清潔使命后，要及時關機，要先關閉高壓清潔設備的電源開關，然后在把電源插頭從電源插座上取下。

7: After finishing the high-voltage cleaning mission, shut down the machine in time. Turn off the power switch of the high-voltage cleaning equipment first, and then remove the power plug from the power socket.

8：當要搬運場所履行新的清潔使命時，CNC高壓清洗機要運用快換接頭拔下高壓泵上的出水高壓膠管，這么才便利對CNC高壓清洗機進行搬運。總之，在操作運用傍邊，要特別注重CNC高壓清洗機的操作，要把安全出產放在頭等主要的方位，這么才干充分發揮高壓清潔設備的效果。

8: When it is necessary to carry out a new cleaning mission in the handling place, the CNC high-pressure washer should use the quick change connector to pull off the water outlet high-pressure hose on the high-pressure pump, so as to facilitate the handling of the CNC high-pressure washer. In a word, in the process of operation and application, special attention should be paid to the operation of CNC high-pressure cleaning machine, and safety production should be put in the first place, so as to give full play to the effect of high-pressure cleaning equipment.

關于輕松使用CNC高壓清洗機得的八大步的相關內容就到這里了，您對此有什么想法或者需求就來我們網站www.glwh.com.cn咨詢吧！

This is all about the eight steps of using the CNC high-pressure washer easily. If you have any ideas or needs, please come to our website www.glwh.com.cn for consultation!